MG8016 Duo 2 encoders Robot dog motor with gear box & RS485 driver Stator 8016 KV30

Product Code: 25480161
Availability: 49999

Price: $593.48
Ex Tax: $593.48

3 or more $581.80
8 or more $575.60
12 or more $569.80

Qty: - OR - Add to Wish List
Add to Compare

25480161 MG8016 Duo Robot dog Motor with Gear box & RS485 Driver, Stator 8016 KV30

Specifications:

Motor	Part No.		MG6010	MG6012 Duo	MG8010	MG8016	MG8016 Duo	MG10015	MG10015
	Turns		20	20	18	13	13	11	11
	Nominal voltage	V	48	48	48	48	48	48	48
	Nominal current	A	3.8	3.8	4.9	6.5	6.5	8	8
	Nominal power		182.4	182.4	240	330	330	385	385
	Nominal torque	N.M	5	5	9	13	13	30	30
	Nominal Speed	rpm	285	285	165	155	155	150	150
	Max Speed	rpm	350	350	250	225	225	190	190
	Stall torque	N.M	11.5	11.5	21	35	35	50	50
	Stall current	A	8	8	7	12.5	12.5	13	13
	Resistance	Ω	0.98	0.98	0.94	0.55	0.55	0.38	0.38
	Wire connect		Y	Y	Y	Y	Y	Y	Y
	Phase to phase inductance	mH	0.55	0.55	0.73	0.54	0.54	0.45	0.45
	Speed constant	rpm/v	58	58	32	30	30	28	28
	Torque constant	N.M/A	1.32	1.32	3.00	3.30	3.30	3.85	3.85
	Radial load	N	1000	1000	1200	1200	1200	2000	2000
	Axial load	N	250	250	300	300	300	500	500
	Rotor inertia	gc㎡	850	850	805	3400	3400	5675	5675
	Number of pole pairs		14	14	20	20	20	21	21
	Motor weight	g	480	480	630	710	710	1190	1190
	Working temperature	C	-20 - 80C	-20 - 80C	-20 - 80C	-20 - 80C	-20 - 80C	-20 - 80C	-20 - 80C
	Max demagnetize temperature	C	120C	120C	120C	120C	120C	120C	120C
Gear	Gear ratio		8:1	8:1	6:1	6:1	6:1	7:1	7:1
Gear	Backlash		5	5	5	5	5	5	5
Driver	Driver No.		DRC15	DRC15	DRC20	DRC20	DRC20	DRC20	DRC20
	Input voltage	V	12-48	12-48	12-50	12-50	12-50	12-50	12-50
	Nominal Current	A	10	10	15	15	15	15	15
	Burst Current	A	20	20	30	30	30	30	30
	Nominal power	W	300	300	700	700	700	700	700
	Communication		CAN Bus	CAN Bus	CAN Bus	CAN Bus	CAN Bus	CAN Bus	CAN Bus
	Encoder		16-bit	16-bit	16-bit	16-bit	18-bit	18-bit	18-bit
	2 Encoders		No	Yes	No	No	Yes	No	No
	Baut rate		1M	1M	1M	1M	1M	1M	1M
	Communication frequency		2K	2K	2K	2K	2K	2K	2K
	Control frequency
	Torque loop	kHz	24	24	32	32	32	24	24
	Speed loop	kHz	8	8	8	8	8	8	8
	Position loop	kHz	4	4	4	4	4	4	4
	Control mode
	Torque loop		Yes	Yes	Yes	Yes	Yes	Yes	Yes
	Speed loop		Yes	Yes	Yes	Yes	Yes	Yes	Yes
	Position loop		Yes	Yes	Yes	Yes	Yes	Yes	Yes
	S-Curve		Yes	Yes	Yes	Yes	Yes	Yes	Yes
	ID Switch		Yes	Yes	Yes	Yes	Yes	Yes	Yes
	Connector		XT2.0	XT2.0	XT2.0	XT2.0	XT2.0	XT2.0	XT2.0
	Temperature sensor		Yes	Yes	Yes	Yes	Yes	Yes	Yes

You are welcome to customize the motor, such as: color, reduction ratio, installation hole position, and other specifications!

Two Encoder Benifits


The first encoder remembers the motor rotor zero postion. The second encoder remembers the gear box output shaft zero position. 1. Turn on the motor power. 2. Send command 3E A6 01 08 ED 00 00 00 00 A0 8C 00 00 2C in Hex to return to Zero position. This above is the Zero position of the motor.	3. Send command 3E A6 01 08 ED 00 00 71 02 A0 8C 00 00 9F in Hex to make the motor return to 267 degree position. The above is the position of 267 degree after run the command. 4. Then turn the motor power off. 5. After a while, turn the motor power on.	6. Send command 3E A6 01 08 ED 00 00 00 00 A0 8C 00 00 2C in Hex to make the motor return to Zero position. The above is motor Zero position after running the command. You can see that the motor with gear box, if there are 2 encoders, even you turn the motor power off, you can return to the motor zero position after power on again.

MG DUO 2 Encoder and 1 Encoder test comparison

Step 1: Power on the motor, run command to set the motors to 0 degree, gearbox to 0 degree.

Step 2: Send the command to run the motor to 150 degree.

Step 3: Power off the motor

Step 4:　Power on the motor again. Send the command to run the motor to 0 degree. You can see both 1 encoder motor and Duo 2 Encoders motor gearbox can return to 0 degree position.

Step 5:　Run command to run the motor to 540 degree.

Step 6: Power off the motor

Step 7: Power on the motor again. Run command to return to motor 0 degree. You can see only Duo 2 Encoders motor gearbox can return to 0 degree position.

Drawing:

Applications:

Open RS485 Protocol

RS485 bus parameter

Bus type:	RS485
Bus interface chip:	MAX3485
Bus interface level:	TTL 3.3V
Baud rate:	9600, 19200, 57600, 115200 (default)
Data bits:	8
Parity:	none
Stop position:	1

2 Some RS485 command samples

The following is a sample to send an open running command to the #1 motor running at 250 power in HEX.
3E A0 01 02 E1 FA 00 FA
The following is a sample to send a Speed closed loop control command to the #1 motor running at an angular speed 720dps in HEX
3E A2 01 04 E5 40 19 01 00 5A
The following is a sample to send a Position + Speed closed loop control command to #1 motor to run at speed 180dps to 360 degree
3E A4 01 0C EF A0 8C 00 00 00 00 00 00 50 46 00 00 C2

Tags: MG8016 Duo 2 encoders Robot dog motor with gear box & RS485 driver Stator 8016 KV30